SMS::Send::DeviceGsm is an SMS::Send driver that uses Device::Gsm
to deliver messages via attached hardware.
You provide the hardware port and the baudrate to use.
Consult Device::Gsm for further information on what devices
and baudrates are supported.
Author: Chris Williams <chris@bingosnet.co.uk>
WWW: http://search.cpan.org/dist/SMS-Send-DeviceGsm/
PR: ports/116531
Submitted by: Tsung-Han Yeh <snowfly@yuntech.edu.tw>
minimal hardware, allows the construction of radios where the
actual waveforms transmitted and received are defined by software.
What this means is that it turns the digital modulation schemes
used in today's high performance wireless devices into software problems.
WWW: http://www.gnu.org/software/gnuradio/
- Diane (VA3DB)
db@db.net
PR: ports/107602
Submitted by: db
1. Update to hylafax 4.3.3
2. Enable JBIG send (receive has to wait for an updated graphics/tiff)
3. Add GHOSTSCRIPT dependency
4. Make portlint a little happier
5. Change "cuaa1" to "cuad1" in pkg-message.in (sigh)
6. Add some @dirrmtry lines to pkg-plist
upgrade of the comms/hylafax from 4.3.3 to 4.3.4
This is an patch to upgrade Hylafax 4.3.3 to 4.3.4
PR: ports/111786, ports/112667
Submitted by: "Eric P. Scott" <eps+pbug0704@ana.com>, Willem Jaap Zwart<W.J.Zwart@NescioLudens.nl>
Approved by: maintainer timeout, maintainer
download datalogs from the Royaltek RBT-3000 bluetooth GPS receiver
(and similar) over a bluetooth link. Based on bluegps-linux.
PR: ports/115012
Submitted by: Dirk-Willem van Gulik <dirkx@webweaving.org>
Firmware for the Broadcom BCM2033 chip based Bluetooth USB
devices. To be downloaded with bcmfw(1). The ubtbcmfw(4)
and ng_ubt(4) kernel modules need to be installed.
PR: ports/115036
Submitted by: Dirk-Willem van Gulik <dirkx@joost.com>
comms/tilp has been superseded by comms/tilp2
It was kept arround until the latter matured, which can now
be considered the case. The original version is no longer
supported by the authors and both ports conflict now. I'm
not sure what exactly should happen, but for me the port
can be removed and maybe added to MOVED.
PR: ports/115979
Submitted by: Tijl Coosemans <tijl@ulyssis.org>
- added 'replstring' substitution option - inspired by
conversation with Owen DeLong <owen@c2company.com>
- added '^Ecn' option for writing a note to the logfile - patch
by Bryan Schmersal <bschmer@yahoo.com>
- fixed leaking file descriptors when 'host' and 'uds' consoles
fail to connect - based on patch by Michael Heironimus
<michael_heironimus@archwayconcepts.com>
Also, the rc.d script now supports "reload", "reconnect",
and "reinit" keywords (they are to send HUP/USR1/USR2
respectively).
Approved by: kuriyama (maintainer)
- Add significantly better support in bsd.python.mk for working with
Python Eggs and the easy_install system
Tested by: pointyhat runs
Approved by: pav (portmgr)
Most work by: perky
Thanks to: pav
supports them. This is determined by running ``configure --help'' in
do-configure target and set the shell variable _LATE_CONFIGURE_ARGS
which is then passed to CONFIGURE_ARGS.
- Remove --mandir and --infodir in ports' Makefile where applicable
Few ports use REINPLACE_CMD to achieve the same effect, remove them too.
- Correct some manual pages location from PREFIX/man to MANPREFIX/man
- Define INFO_PATH where necessary
- Document that .info files are installed in a subdirectory relative to
PREFIX/INFO_PATH and slightly change add-plist-info to use INFO_PATH and
subdirectory detection.
PR: ports/111470
Approved by: portmgr
Discussed with: stas (Mk/*), gerald (info related stuffs)
Tested by: pointyhat exp run
